Death Valley Ride Report: Day 3, Towne Pass

  • Motorcycle Miles: 55
  • Bicycle Miles: 29

A little bit about my original cycling Death Valley plan:  Originally I was thinking I’d tackle 2 climbs per day, get up early.. ride one.. relocate to the start of the next, ride another.  Just looking at the bicycle parts, that’s not super crazy – I’ll do 7000 ascent as a regular ride, and if I just do the climbing vs. droning along boring flat stuff, the actual saddle time would be shorter.

However, riding a motorcycle is also tiring.  So is packing, unpacking and camping.  After Wildrose, I headed over to camp at Panamint springs.  Originally I was going to ride Towne pass back-to-back with Wildrose – I quickly abandoned that idea and decided to ride it the next day, and if I was feeling good, ride both sides.

wp-1490582489722.jpg
Also handy, your bike rack can act as a clothes line!

Once again, up early (due to heat) and headed out to climb Towne pass.  Starting from the Panamint side is definitely easier, here’s the view going up.

wp-1490582584680.jpg
Panamint valley facing up Towne

This climb is mostly just a grind on up, there was the occasional car, but nothing really notable.  Despite it being in the Top 100, I wouldn’t have been real sad if I skipped it.

wp-1490582678866.jpg
Sometimes ya gotta stop and pee

After about an hour and a half, I reached the summit and had to decide if I was going down the other side!

wp-1490582745520.jpg

Actually this wasn’t a difficult decision – I was tired out.  For my longer trip, I think back-to-back motorcycle-bicycle riding is probably not a great idea.  I’ll need to be more selective about which climbs I choose.

I pointed my way back to camp and hauled down hill, sitting up the entire way, hoping not to overheat my brakes.  These long Death Valley climbs make it real easy to hit 50+ mph.  I was still on my small knob CX tires, so this was not an experiment I was keen to try out.  I’ll be back on near-slick tires for the multi-week trip!

wp-1490582819167.jpg
Panamint valley floor.  Epic.

Back to camp to shower, pack up, and wait out the heat before heading over to Furnace Creek (55 miles by motorcycle.)

towne2

 

Death Valley Ride Report: Day 2, Wildrose

  • Motorcycle Miles: ~135
  • Bicycle Miles: 33.7 / 5600 feet ascent

Alright, this is it.  When planning this trip, there were 2 climbs I really wanted to do:  Wildrose to the Kilns, and Dante’s View.  I knew Wildrose was going to be a challenge, because of several factors:  1) it is in the middle of no where, truly the exact sort of climb I wanted to target for this adventure 2) the road is closed, and it has been for some time due to washouts, land slides, deep gravel, etc. 3) the weather forecast was getting worse and worse, now looking like mid-90s.

Now add that this is the first climb of the trip, because it was “on the way” from Kernville, it was setting up to be a bit of a nervous time.

DISCLAIMER TIME:  Riding a motorcycle is dangerous.  Riding a bicycle is dangerous.  Riding either of these in Death Valley is extra dangerous.  Doing one, or both of these, ALONE in Death Valley, is not to be taken lightly.  I carry enough food and water for double what I expect to encounter.  I carry a certified PLB (Personal Locator Beacon) in case of true emergency, but basically I assume I’m on my own for 24+ hours. I aim to be at 50% at all times (50% of food, 50% of water, 50% of my bicycling capability, 50% of motorcycle grip, etc.)  That way when I go over the limit by accident or mishap or surprise, I don’t die.

Alright, up ~2 hours before dawn, drank coffee, bicycle kit on, motorcycle kit on top of bicycle kit.. and a rather precarious 2 hour motorcycle trip in the dark to the Panamint valley side of Death Valley.  This illustrated a challenge:  I have not been riding my motorcycle very much and am badly out of practice.  More riding required.

After a quick gas stop in Trona, the sky started getting light and the vastness of the desert opened up.  Droning another 45 minutes through the middle of no where, brought me to the Wildrose turn off.  It is literally, a turn off into no where.

wp-1490538702884.jpg
Lower Wildrose Road, off Panamint Valley

A little bit on the “Road Closed” – road conditions can change very rapidly in Death Valley, as nearly all the roads run along natural “washes” (normally dry river/creek beds) – so any precipitation will rapidly reconfigure conditions.  In this case, there had been no precipitation for a few weeks, and I had reliable reports from motorcyclists & 4x4ers about potential conditions.  At worst, it sounded like a few sections of hike-a-bike.

The main risk would be lack of traffic – no one was going to rescue me if I had a mechanical or injury.  But see above disclaimer, I was pretty well prepared and riding cautiously.

First observation:  Changing from motorcycle to bicycle takes a lot longer than you would think.  Without really rushing, I’d say it took me 20+ minutes before I was ready to roll.  It’s just a lot of bits and pieces to move around, bolt together, lock together, etc.

For my longer trip, this type of ride will definitely need to be an exception vs. norm.

I was somewhat nervous leaving my motorcycle & kit.. but hey, that’s part of this trip too, can I deal with possibly coming back and having no gear or motorcycle?!  I did leave a note strapped to my bike in a document holder:

“Hi, I’m off bicycling and/or hiking for a few hours.  I have plenty of food, water, and a GPS emergency beacon.  Please don’t mess with my motorcycle or gear, I will need it when I get back so I don’t die.  Thanks.  Emergency contact xxxxx.”

Okay, off to bicycle – and as expected, yeah, there was some gnar on the closed road section.  Deep gravel, washouts, some mud starting around 3500 feet.  This ended up using a lot more watts than I anticipated, as pedaling through deep gravel requires a fair amount of watts or you fall over and/or stop and walk.  Luckily there was only one section that I couldn’t actually pedal through, so I walked maybe 100 feet.

This overall section was probably the highlight of the trip.  It was interesting, it was unknown, and it was EMPTY.  When you are alone in Death Valley, you are REALLY alone. I saw not a soul until reaching the intersection with Charcoal Kilns road about 3/4 up.

wp-1490538753154.jpg
Halfway up Wildrose canyon

Once past the closed section, you junction up with Charcoal Kilns Road, which takes you up to the old kilns that were used to make charcoal for the various smelters in the area.

This is more typical Death Valley – vast vistas and basically nothing.

wp-1490538901109.jpg
Charcoal Kiln road about halfway up

The segment I had loaded on my Wahoo ELEMNT was from John @ PJAMM, which was labeled “2 miles past dirt” – well lemmie tell ya, that dirt was the worst.  Lots of washboard, rocks and gravel.  Both challenging and unfun.

Double unfortunate, that segment didn’t go all the way up.  So when I was “done” – I had 20 more minutes of climbing to do, all of it from to 10-14% grade.

Eventually I made it up to the 2nd gate (the road continues further past the 2nd gate, but stuck to my plan to turn around here, given the potential heat down in the valley, etc.)

I had just finished off my 2L camelbak at this point, so I still had 2 full water bottles.

The valley heat was not far from my mind, so I hit the descent.  This was even worse going down.  Heavy washboard is the one thing a rigid gravel bike is really bad at.  So it was slow, riding the brakes for several miles of dirt road.  Once I hit the pavement, it was 40+ mph until the turn off to the closed section.  Having some experience going up, this was not as bad going down since I could float over most of the gravel sections at a reasonable speed.

Back at the bottom, air temperature was around 87F.  Not too bad, but glad I didn’t hang around.

wp-1490539068186.jpg
Yay, motorcycle still here!  You can also see my Pacsafe gear wrapped up on the motorcycle seat.

wildrose

Here’s the Strava segment.  Note on John’s page, this is #56 with a Fiets score of 8.64, but as noted above, I kept on going for another 20 minutes of 10-14% grade.  Plotting my route on ridewithgps.com returns a Fiets score of 11.64, which would put this climb up in the Top 20 in the country.  Add in the remoteness, it was no surprise I had to create a new Strava segment to cover it!

After mounting the bicycle and donning my motorcycle gear, I motorcycled the remaining 15 miles to Panamint Springs to camp overnight.

 

Death Valley Ride Report: Day 1

  • Motorcycle Miles: 300
  • Bicycle Miles: 0

Kernville is a nice little stop over on the way to Death Valley, and approximately 120 miles away from my first bicycle climb.

I took Highway 25 down the central valley, cut over to I5 to test out the motorcycle-bicycle rig on the horrors of Interstate 5, and then took 178 along the Kern River to Kernville.

The rig behaved pretty well, but definitely requires awareness when dealing with tractor-trailer buffeting.  Riding no hands would be ill-advised.

wp-1490536497898.jpg
One of many diversions, this one along Highway 25 in San Benito county

 

Death Valley Preparation 2: Don’t I also need a bicycle?

2 days before leaving and spending a lot of time figuring out my packing logistics, I figured I should probably also mount up the bicycle I was planning to take both on this trip, and my extended June trip.  This is a generic China carbon CX frameset, configured with hydraulic disc brakes and ultra low gearing (44/30 + 10-42 cassette!) – the main difference between this and my Parlee is the thru-axle fork configuration.  The 2×2 rack is transformable for both QR & Thru-axle, so I didn’t think too much of it.

One thing to address right away is ensuring I had a disc brake spacer to avoid compressing the pads together on accident.  So tossed an extra spare one into my spare bag, this also adds a setup/tear down step.

Next up, I went to attach the bike and realized my China fork’s dropout was too small to mate over the outside of the 2×2 rack.

The “shoulder” on the fork was approximately 1.5 mm too narrow to sit nicely on top of the rack.

So, like any good Motorcycle Farkler.. I broke out the Dremel and some sanding discs and ground down the rack “axle” so it would fit.  Having a tight interface here is critical to avoid damage to the fork, given all the forces that are going to be put on it.

wp-1490534340505.jpg
2×2 rack modification for my Chinese fork

 

Once I had the fork mounted I gave it a good shake and noticed there was still a fair amount of movement between the rack & the fork dropout.  Again, this is the major interface to the bike/rack, so any movement here is a bad thing.

More measuring and it appears my Chinese fork axle is ~14.6mm, and the inside diameter of the bike rack is ~16.6mm.  The result is that the axle can “wobble” in the rack, rubbing the dropouts.  Time for more Farkle creativity – a layer of heat shrink tubing over the axle, hit it with the heat gun, cooled and sliced off as a spacer.

2x2 rack through axle thru axle spacer
Heat shrink tubing spacer and ground down “axle” for my fork

This is still not ideal since it is made of rubber, but 48 hours to launch you use what ya got.  For my longer trip I will replace with some aluminum can shim or stainless sheet.

Final challenge:  Stages power meter lives on the same crank arm that secures the back end of the bicycle.  For this I glued & zip tied a few layers of thick rubber as a spacer against the crank arm.

Done!  Bicycle attached, 48 hours to go!

wp-1490535401045.jpg
Loaded up and ready to go!

Death Valley Preparation 1: Packing for Bicycle/Motorcycle Adventuring

Reviewing PJAMM’s “Top 10o U.S. Climbs” I quickly noticed there’s a bunch that are unlikely to be possible to ride at the height of summer, especially anything in Death Valley.  I’ve been through Death Valley on my motorcycle in 2011, as well as riding through once in late Fall and the heat on the valley floor is something difficult to describe.  So I mentally crossed these off the plan for June.

However, while I was experimenting with my whole moto-bicycle scheme, some buddies were planning a parallel dual sport motorcycle trip for early March to the same area.  And after my successful Diablo ride I needed a longer, multi-day, with camping, multi-point moto-bicycle trip to practice with.. so.. why not leap straight to “difficulty level 10” in logistics and piggy-back onto their trip?  That way I have some people in the local area if things go off the rails.

Unfortunately for me, I’ve had a bit of a nagging hip issue for the past month.  I’m pretty sure I didn’t injure it while bicycling, since it is barely noticeable while on the bike but it was improving slowly enough it was difficult to say.  So, in short, I didn’t decide to go on this trip until a week before launch, and even then I was probably 50/50 until 2 or 3 days before.

You can see where this is going.  One of the biggest challenges of motorcycle-bicycle-camping-extended-trip is packing logistics.  Volume is king on the motorcycle, and the bicycle steals both space for bags and adds a lot of volume with shoes, helmet, water bottles, food, etc.  Also a small issue was that the bike I plan to take on the trip is not the bike I put on for the Diablo trip..

20170322_055621.jpg
Less than ideal packing strategy

For longer trips, I love my Wolfman Expedition Medium Duffle (Amazon)

61wdghaxt2bl-_sl1000_
Wolfman Duffle – Amazon

– it holds everything I need to set up camp – tent, cot, jetboil, camp chair, mini-hatchet, etc.  Unfortunately this bag is both too big to comfortably fit behind the bicycle fork, and since it is a top roll, “transformation time” would be extended.  Given the kit I had available due my last minute decision, I rolled with my Kriega US20.  This held my spare motorcycle tube, pump, and first aid kit, in addition to the items I would use while bicycling:  Pacsafe squid, stuff sack for my motorcycle gear, bicycle shoes, hydration pack, bicycle tail pack with tube/spares/etc, bicycle handlebar bag with food, emergency beacon, glow stick, water filter, e-blanket, etc.

With so much loss of volume, my “luxury camping” gear went out the window – no tent, no stove, no camp chair.  I figure combining bicycling and motorcycling doesn’t leave much time for camp setup/tear down anyways, so going for speed here is probably more realistic.

The one item I’ll never camp without is the LuxuryLite UltraLight Cot (Amazon)

61d7bimyial-_sl1000_
Therm-a-rest LuxuryLite Cot – Amazon

– if you’re a side sleeper, this is THE camp bed to have.  I wake up stiff and crippled on anything else (and I’ve tried plenty!)

So what I was left with:

Kriega across the top plate:  Motorcycle tube/pump & first aid kit, bike shoes, Pacsafe, gear stuff sack, hydration pack, bicycle tail & handlebar pack.

Left case, camping & non-daily used stuff:  Cot, Marmot Never Summer (Amazon) sleeping bag, OR Helium Bivy Sack (Amazon), travel bicycle pump, beach towel, bag with misc straps, couple of stakes, etc.

Right case, day-to-day stuff: clothes bag, bicycle kit bag, bike helmet filled with ride stuff (bike computer, HR strap, gloves, skull cap, etc.), bicycle tools/spares/batteries/etc, bath & hygiene stuff.  I also put my water bottles for the bicycle in here since there was room to keep them upright and not leaking all over.

Tank bag (Giant Loop Diablo – Amazon) – Usual ride-all-day stuff:  hat, sunscreen, bug repellant, ibuprofen, chapstick, camping headlamp, etc.  This also holds my CamelBak hydration bladder, which during bicycling with no water available will transfer into my hydration pack.

So, the bicycle transformation plan with this kit:

  • Remove & assemble bicycle
  • Kriega
    • Remove Pacsafe & stuff sack for motorcycle gear
    • Pull out hydration pack
    • Attach tail pack & or front pack to bicycle
    • Pull out bike shoes
  • Side case
    • Remove helmet & gloves/windbreaker/etc
    • Pull hydration bladder from the tank bag and put into hydration pack
    • Put tank bag where the helmet was in the side case
    • Attach water bottles to bicycle
  • Clothing dance
    • Jacket into stuff sack.  Stuff sack + pants + boots into Pacsafe, secure to motorcycle with cable & lock
    • Lock helmet to frame
    • Put on all the bike stuff
  • Go ride!

2×2 Cycles Motorcycle Bicycle Rack Install and Mount Diablo Shakedown

So ordered up the 2×2 rack and received it promptly.  I pondered removing my Moto Overland Top Plate and bolting it straight to the bike. I wasn’t real confident in getting my elaborate stack of bolts, washers, spacers, Hepco Becker side case racks, etc., back together. In the end decided to just bolt it to the existing plate with a bunch of bolts and washers.  Time will tell if this is a bad idea.

dsc_0897.jpg
Rack sandwich

I went ahead and test fit my road bicycle (Parlee Z5SLi) and was very happy with the security and fit.  With the exception of being concerned of the exhaust outlet in relation to the front wheel storage:

20170320_165840.jpg
Aftermarket exhaust outlet behind front tire

Now this is probably ok, there’s a good 8 to 10 inches between the exhaust outlet and the tire.. but given what I was planning, I emailed Garret @ 2×2 and he leapt into action, welding up a custom bracket that will move the tire up or back 3-6 inches, I rode Diablo without it, but here’s what it looks like:

dsc_0898.jpg
Bracket is reversible, for up or back orientation, with a clever tab welded on so it can’t rotate.

Okay, great, we got a bike on a rack, now we need to take it some where.  Embarrassingly, despite living in the bay area for 20+ years, I have never bicycled up Mt Diablo.  So I chose this as my destination.  I picked a convenient Starbucks ~50 miles away near the foot of the climb, loaded up, and headed out.

First observation:  My motorcycle+bicycle is a SPECTACLE. People were swerving around on the freeway, zooming up next to me to take a picture, etc.  This was a little unnerving, I couldn’t tell if I was losing parts or something else was happening.  Please don’t take my picture while driving your car!

For this ride, I wore my bicycle kit under my motorcycle gear (Aerostich Darien Jacket and Pants) and my side cases were entirely empty.

Here’s me parked and getting ready to transform:

dsc_0813.jpg
Yeah, people stared. Children were confused.

I quickly realized I would need to find some other solution to stashing my gear while out bicycling – it literally filled both cases completely, along with a helmet lock to bolt my helmet below my side case.  That won’t leave much (any) room for a month’s worth of travel and camping gear.  Later I did some research and found the Pacsafe Backpack and Bag Protector (Amazon) – it sorta looks like a squid mated with a bicycle cable lock.  It certainly won’t stop anyone determined to mess with your stuff, but will hopefully deter a lazy snatcher.

pacsafe
Pacsafe (Amazon)

Alright, so after 15 or 20 minutes of changing and packing and bolting the bike back together, time to roll!

diablostrava
Click image for full Strava activity

Road conditions were pretty sketchy – lots of dirt, gravel, some water.  I started on the south side went to the summit, then blasted down the north side and back up again.

dsc_0808.jpg
West side!
dsc_0810.jpg
East side!

Alright, back at Starbucks.. time to transform!  Since every cyclist and motorcyclist knows the danger of saddle sores, gotta get those bike shorts off and clean up.. how?  Well, for the Rock Cobbler “extreme gravel grinder” there was a sample of On The Go Towel Wipes (Amazon)

417tbsk0ydl
Wipes – Amazon

– these are much much better than baby wipes.  Far more substantial and you don’t smell like babies.  Along with a beach towel and a fresh pair of shorts, I performed the Reference Standard Beach Change and was back in motorcycle gear.

Conclusion:  This is doable.  Needs multi-day and long distance test!

Why motorcycle with a bicycle?

Well, this goes back a bit.  I’ve been motorcycling for a while.  I’ve been bicycling for a while.  ~5 years ago, I spent 4 weeks riding my motorcycle around Canada and Alaska.

ac

As my next 5 year sabbatical approached, I began planning what I thought would be a motorcycle trip down the Continental Divide (from the Canadian border down to Mexico.)

I also started recovering from my latest injury and began bicycling more, culminating in participating in a local hill climb series (shout out to Low Key Hill Climbs!) as well as dropping the latest 30 pounds I gain every time I get injured.

I figured I should use my current cycling form for something, and decided I should at least ride all the top climbs in California this summer.  Which lead to John Summerson’s “Complete Guide to Climbing by Bike” book.

51ue-vpn0hl-_sx320_bo1204203200_
Amazon

Which lead me to PJAMM cycling’s “Top bike climbs in the United States” web page.  Which lead to pondering how many of the Top 100 climbs I could visit in 4 to 6 weeks of traveling.

Unfortunately for me, I loathe long car road trips.. but I can ride my motorcycle day after day forever, no problem.

A quick Google for “bike racks for motorcycles” turned up the most excellently engineered 2×2 Cycles Rack and a vague sketch of a plan formed in my mind:  I would travel around the western US with my motorcycle AND bicycle.  Motorcycle to the foot of a remote climb, switch to bicycle, ride it, then switch back!  CRAZY!

Crazy enough people said I should blog about my experiences, including my lovely wife.  I don’t do Facebook, my Instagramming is inconsistent, and Strava only covers a small aspect of it.  Plus, I’m capturing my own learnings and actions as I go along.

So, here it is… count-down to (probably) June.  Please leave a comment if you’re interested in any particular aspect of this craziness!

This is, so far, my deeply thought out plan (each balloon or diamond represents a notable climb.)

routeplan
Route planning via MS Paint!